DATCON

DT 6000 fetures:

• different type of unit version (UVI, W/m²)
• 3 1/2 digits LCD display with 12.7 mm character height
• handheld version
• quick sets
• 5 % accuracy

DT9000 / DT9002 features:

• Display in engineering units
• 4 1/2 digit LCD, 20.5 mm character height
• 4-20 mA loop powered
• Min / Max values detection
• 2 isolated limit outputs
• 0.03 % accuracy, ±20 ppm / °C
• Intrinsically safe (zone 1, 2)
• Easy on-site configuration
• IP 65 protection
  IP 30 rear protection (DT9002)

Product features:

• Transient voltage protection of the 4-20 mA current loop
• 3-stage protection
• 10 kA surge vawe (8 / 20 µs)
• 41 V max. Output noise voltage
• DIN rail mounting and IP 65 enclosure version

DT2014 features:

• 4 x 22 VDC, 25 mA stabilized outputs
• Outputs are galvanic isolated from each other
• Overcurrent-protection with limiter characteristics
• 190-250 VAC / 90-250 VDC power supply ranges
• TS-35 rail mounting 12.5 mm width only

Product features:

• 8 x NAMUR / contact inputs
• Counting of incoming pulses
• Measuring the time between the incoming pulses 
• RS232 / RS485 communication, MODBUS RTU protocol
• Configuration via USB port
• 24 V AC/DC, 230 V AC/DC power supply
• TS-35 rail mounting, 45 mm width

Type designation:
DEMS5005 RS2 20-50 VDC / 19-35 VAC power supply, RS232 interface
DEMS5005 RS2  PS 90-250 V AC/DC power supply, RS232 interface
DEMS5005 RS4 20-50 VDC / 19-35 VAC power supply, RS485 interface
DEMS5005 RS4  PS 90-250 V AC/DC power supply, RS485 interface

Product features:

• More then 50 different measured parameters
• 3 x 0-125 VAC / 0-250 VAC non galvanic isolated voltage input
  3 x 0-5 AAC / 0-1 AAC galvanic isolated current input
  CAT III category
• Different measuring arrangement
• 2 x 0-20 mA / 4-20 mA galvanic isolated outputs
• RS485 interface, MODBUS RTU/ASCII Slave protocol
• 2 x Pulse outputs / Limit-relay outputs
• Configuration by PC via USB port
• 19-35 VAC / 20-50 VDC or 90-250 V AC/DC power supply
• TS-35 rail mounting, 22.5 mm width

Product features:

• More than 50 different measured parameters:
  Ueff, Ieff, f, P, S, Q, PF, φ, +EP, -EP, +EQ, -EQ (each phase)P, S, Q, PF, +EP, -EP, +EQ, -EQ (sum)UL1-L2, UL2-L3, UL1-L3, φL1-L2, φL1-L3 (between phase)P1/4h average value, P1/4h estimated average value, Plast 1/4h average value, t1/4h rest (demand)
• 3 x 0-125 VAC / 0-250 VAC / 0-450 VAC,
  3 x 0-5 AAC / 0-1 AAC galvanic isolated inputs
  CATIII measurement category
• 2 / 4 x 0-20 mA / 4-20 mA galvanic isolated outputs
• RS232 / RS485 / ETHERNET interface
  MODBUS RTU slave / MODBUS TCP, HTTP protocol
• 2 limit-relay outputs
• Synchronous and time zone signal inputs
• Pulse outputs
• Configuration via USB port
• 24 V AC/DC, 230 V AC/DC power supply
• TS-35 rail mounting, 90 mm width

Product features:

• Measuring of 14 different single phase parameters:
  Ueff, Ieff, P, Q, S, +Ep, -Ep, +EQ, -EQ, PF, f, ϕ, THD U, THD I
• 0-125 VAC / 0-250 VAC non galvanic isolated voltage input
  0-5 AAC / 0-1 AAC galvanic isolated current input
  CAT III measurement category
• 2 x 0-20 mA / 4-20 mA galvanic isolated outputs
• MODBUS RTU/ASCII Slave communication
• 2 x Pulse outputs / Limit-relay outputs
• Configuration by PC via USB port
• 19-35 VAC / 20-50 VDC or 90-250 V AC/DC power supply
• TS-35 rail mounting, 22.5 mm width

Product features:

• Measuring of 12 different parameters:
  Ueff, Ieff, P, Q, S, +Ep, -Ep, +EQ, -EQ, PF, f, ϕ
• 0-125 VAC / 0-250 VAC / 0-450 VAC and
  0–5 AAC / 0–1 AAC galvanic isolated inputs
  CATIII measurement category
• 2 x 0-20 mA / 4-20 mA galvanic isolated outputs
• RS232 / RS485 / ETHERNET communication interface
  MODBUS RTU slave / MODBUS TCP, HTTP protocol
• 2 limit-relay outputs
• Synchronous and time zone signal inputs
• Pulse outputs
• Configuration via USB port
• 24 V AC/DC, 230 V AC/DC power supply
• TS-35 rail mounting, 45 mm width

Product features:

• 0–20 mA / 4–20 mA / 0–10 V / 2–10 V / 0–5 V inputs
• 2 / 4 x limit-relay outputs
• Process indicator function
• 5 digit LED display, 7,6 mm character height
• Menu based configuration 
• 0–20 mA / 4–20 mA isolated output
• Transmitter supply
• 18–40 V DC / 14–29 V AC power supply or 140–250 V AC / 180–250 V DC mains
• TS-35 rail mounting, 45 mm width