DATCON

Product features:

• Any output voltages between 6-24 VDC range
• 6 / 8 / 10 / 12 / 15 / 18 / 24 VDC nominal output
• Overcurrent-protection
• Overvoltage-protection
• 230 VAC power supply
• TS-35 rail mounting, 35 mm width
• 11 different types

Product features:

• Pt100 / Pt500 / Pt1000 inputs
• Resistance / potentiometer inputs
• 2 / 3 / 4 wire measurement
• -200°C-800°C / 0-4000 ohm input ranges
• 0-20 mA / 4-20 mA / 0-10 V / 2-10 V output ranges
• 0,03% accuracy
• Easy configuration via IR transmission
• 19-35 VDC supply voltage
• TS-35 rail mounting, 12.5 mm width

Product features:

• NAMUR / contact inputs
• Relay contact / transistor outputs
• 1 / 2 / 4 channel versions
• Line fault detection
• Switch selectable mode of operation
• 3 kHz transmission frequency (transistor output)
• 19-29 VDC supply voltage
• 12.5-22.5 mm széles, TS-35 sínre pattintható kivitelek
• 11 different types

Product features:

• 0-20 mA / 4-20 mA / 0-10 V inputs
• 0-20 mA / 4-20 mA / 0-10 V outputs
• Non-linearity < 0,01%
• Temperature-coefficient < 50 ppm / °C
• 19-29 VDC supply voltage
• TS-35 rail mounting, 12.5 mm width
• 9 different types

Product features:

• 0-20 mA / 4-20 mA / 0-10 V inputs
• 0-20 mA / 4-20 mA / 0-10 V outputs
• 17 VDC / 18 VDC transmitter supply
• Non-linearity < 0.01%
• Temperature-coefficient < 50 ppm / °C
• 19-29 VDC supply voltage
• TS-35 rail mounting, 12.5 mm width
• 18 different types

Product features:

• 3 x 0-125 VAC / 0-250 VAC galvanic isolated voltage inputs
  3 x 0-5 AAC / 0-1 AAC galvanic isolated current inputs
  CATIII measuring category
• Neutral current measurement
• Harmonic analysis and THD measurement on voltages and currents
• Flicker measurement
• Voltage asymmetry measurement
• Network analysis according IEC61000-4-30
• Storage trends, evens and ADC samples on SD card
• Colour TFT graphics display
• RS485 / Ethernet interface
  MODBUS RTU / ASCII slave / MODBUS TCP, HTTP, FTP, SMTP protocol
• 0-20 mA / 4-20 mA galvanic isolated transmitter outputs
• RS485 interface, MODBUS RTU/ASCII slave protocol
• Digital outputs (Pulse output, Limit output)
• Menu settings
• 19-35 VAC / 20-50 VDC vagy 90-250 V AC/DC power supply
• 96 x 96 mm panel instrument

Product features:

• More than 50 different measured parameters on 3 phase network
• 3 x 0-125 VAC / 0-250 VAC non galvanic isolated voltage inputs
  3 x 0-5 AAC / 0-1 AAC galvanic isolated current inputs
  CATIII measuring category
• Many measuring arrangement: network with or without neutral, 1/2/3 power input(s)
• Graphics display
• 0-20 / 4-20 mA galvanic isolated transmitter output
• RS485 interface, MODBUS RTU/ASCII slave protocol
• Pulse output, Limit outputs
• Settings menu
• 19-35 VAC / 20-50 VDC or 90-250 V AC/DC power supply
• 96 x 96 mm panel instrument

Product features:

• More than 50 different measured parameters on 3 phase network
• 0-125 VAC / 0-250 VAC / 0-450 VAC
  0-5 AAC / 0-1 AAC galvanic isolated inputs
  CATIII measuring category
• 4 x 16 character alphanumeric display
• 0–20 mA / 4–20 mA galvanic isolated outputs
• RS485 / RS232 / ETHERNET interface
  MODBUS RTU slave / MODBUS TCP, HTTP protocol
• Limit-relay outputs
• Pulse outputs
• Synchronous and time zone signal inputs
• 24 V AC/DC, 230 V AC/DC power supply
• 96 x 96 mm panel instrument

DT4200 / DT420 E features:

• Display in engineering units
• 4 1/2 digit LCD display, 15 mm character height (DT4200)
  3 1/2 digit LCD display, 15 mm character height (DT420 E)
• 4–20 mA loop-powered
• 2 isolated limit outputs
• Min / Max values detection
• 0.01% accurary, ±20 ppm / °C (DT4200)
  0.02% accuracy, ±20 ppm / °C (DT420 E)
• Easy on site configuration
• IP 65 front side
  IP 30 rear side